How to change ignitioncoil on BMW E82-replacement guide

   

 This article mainly introduces How to change ignitioncoil on BMW E82-replacement guide

 

How to change ignitioncoil on BMW E82-replacement guide

REPLACEMENT:IGNITION COIL-BMW E82.TAKE THE FOLLOWING STEPS:


1 Open the hood.

2 Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

3Unscrew the fasteners of the cabin filter housing cover.Use a drive socket #8.Use a ratchet wrench.

4 Remove the cabin filter housing cover.



5 Remove the wiper arm covers.



6 Detach the connectors from the climate control sensors.


7  Remove the climate control sensors.
 8  Unscrew the fasteners of the lower part of the scuttle panel.Use a drive socket #8.Use a ratchet wrench.

g Detach the cable duct from the upper part of the microfilter housing.Use a flat screwdriver.

10| Remove the lower part of the scuttle panel.

11 Unscrew the engine cover fastener.Use HEX No.H5.Use a ratchet wrench.



12Remove the engine cover.

13 Detach the connector from the ignition coil.

14 Treat the ignition coil connector with electronic spray. The spray will protect the electrical contacts from corrosion, oxidation, and will reduce the contact resistance.

15Take out the ignition coil from the spark plug well

16Treat the ignition coil tips.Use high-temperature grease.Use a flat screwdriver.

17Install the new ignition coil to the spark plug well.Make sure you hear a click indicating that it is locked in place.

18|Plug in the ignition coil connector.

19|Install the engine cover and secure it.

20 Screw in the engine cover fasteners.Use HEX No.H5.Use a ratchet wrench.

21 Reinstall the lower part of the scuttle panel.

22|Screw in the fasteners of the lower part of the scuttle panel.Use a drive socket #8.Use a ratchet wrench.

23| Install the climate control sensors.

24 | Attach the connectors of the climate control sensors.

25 Install the wiper arm covers.

26 Attach the cable duct to the upper part of the microfiter housing.

27 Reinstall the cabin filter housing cover.Make sure you hear a click indicating that it is locked in place.

28 Screw in the fasteners of the cabin filter housing cover.Use a drive socket #8.Use a ratchet wrench.

29 | Remove the fender protection cover.

30 Close the hood.

31Run the engine for a few minutes.This is necessary in order to make sure that the component operates properly.

REPLACEMENT:IGNITION COIL-BMW E82.TAKE THE FOLLOWING STEPS:

1 Open the hood.

2 Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

3Unscrew the fasteners of the cabin filter housing cover.Use a drive socket #8.Use a ratchet wrench.

4 Remove the cabin filter housing cover.

5 Remove the wiper arm covers.

6 Detach the connectors from the climate control sensors.

7 Remove the climate control sensors.

8 Unscrew the fasteners of the lower part of the scuttle panel.Use a drive socket #8.Use a ratchet wrench.

g Detach the cable duct from the upper part of the microfilter housing.Use a flat screwdriver.

10| Remove the lower part of the scuttle panel.

11 Unscrew the engine cover fastener.Use HEX No.H5.Use a ratchet wrench.

12Remove the engine cover.

13 Detach the connector from the ignition coil.

14 Treat the ignition coil connector with electronic spray. The spray will protect the electrical contacts from corrosion, oxidation, and will reduce the contact resistance.

15Take out the ignition coil from the spark plug well



16Treat the ignition coil tips.Use high-temperature grease.Use a flat screwdriver.

17Install the new ignition coil to the spark plug well.Make sure you hear a click indicating that it is locked in place.

18|Plug in the ignition coil connector.

19|Install the engine cover and secure it.



20 Screw in the engine cover fasteners.Use HEX No.H5.Use a ratchet wrench.

21 Reinstall the lower part of the scuttle panel.

22|Screw in the fasteners of the lower part of the scuttle panel.Use a drive socket #8.Use a ratchet wrench.

23| Install the climate control sensors.

24 | Attach the connectors of the climate control sensors.



25 Install the wiper arm covers.

26 Attach the cable duct to the upper part of the microfiter housing.

27 Reinstall the cabin filter housing cover.Make sure you hear a click indicating that it is locked in place.

28 Screw in the fasteners of the cabin filter housing cover.Use a drive socket #8.Use a ratchet wrench.

29 | Remove the fender protection cover.

30 Close the hood.



31Run the engine for a few minutes.This is necessary in order to make sure that the component operates properly.

How to change frontwheel bearing on BMW E39-replacement guide

 This article mainly introduces  how to change frontwheel bearing on BMW E39-replacement guide

09.2022 BMW Rheingold ISTA+ 4.37.22 & ISTA-P 3.70 With PSdZData Full Download Service

 

 Replacement: wheel bearing -BMW E39. AUTODOC experts recommend:

1. Do not re-use thel bearing assembly of your BMW E39 car.

2. The wheel hub bearing replacement procedure is identical for both wheels on .

3.Warning! Shut down the engine before starting any work-BMW E39.

CARRY OUT REPLACEMENT IN THE FOLLOWING ORDER:

 

BMW E-sysPlus 3.8+4.33.31 PsdZdata Lite

1  Secure the wheels with chocks.

 

 

2  Loosen the wheel mounting bolts. Use wheel impact socket #17.

 

3  Raise the front of the car and secure on supports.

 

 4  Unscrew the wheel bolts.

 

BMW E-Sys Scripts Collection for New Features

3 Replacement: wheel bearing-BMW E39. Tip:

To avoid injury, hold up the wheel when unscrewing the bolts.

 5  Remove the wheel.

 

6  Remove the dust boot caps of the brake caliper guide pins.Use a crowbar.

 

7  Unscrew the brake caliper fastening.Use HEX No.H7.Use a ratchet wrench.

 

8  Spread the brake pads.Use a crowbar.

 

9  Detach the brake caliper retaining spring.Use a crowbar.

 10| Remove the brake caliper.

 

Replacement: wheel bearing -BMW E39. AUTODOC recommends:

l Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.

l Make sure that the brake caliper is not hanging on the brake hose.

l Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.

l Check the brake caliper bracket, brake caliper guide pins and boots. Clean them.

Replace, if necessary.

 11  Remove the brakepads.

 

12|  Clean the brake caliper bracket fasteners.Use a wire brush.Use WD-40 spray. 3

13  Unscrew the caliper bracket fastening.Use a drive socket #18.Use a tap wrench.

14| Remove the caliper bracket.

 15 Clean the brake disc fasteners.Use a wirebrush.Use WD-40 spray.

 16 Unscrew the brake disc fastening.Use HEX No.H6.Use an impact screwdriver.

17 |Remove the brake disc.

Replacement: wheel bearing-BMW E39. Tip:

If necessary, use a rubber mallet.

 18 Clean the wheel hub fastener.Use a wire brush.Use WD-40 spray.

 19|Unscrew the wheel hub axle nut.Use a combination spanner #18.

 20| Remove the hub and the bearing together, since they are a sealed unit. Use a hammer.

 21Clean the hub bearing mounting seat.Use a wire brush.Use allpurpose cleaning spray.

 22 Install the new wheel hub with a bearing.

 23 |Tighten the hub.Use a drive socket #18.Use a torque wrench.Tighten it to 110 Nm torque.

 Replacement:wheel bearing -BMW E39.Tip from AUTODOC:

 he wheel bearing unit must not tilt on the axle pin.

 24Treat the hub where it contacts the brake disk.Use copper grease.

 25|Install the brake disc.

 26 Tighten the brake disc fastening.Use HEX No.H6.Use a torque wrench.Tighten it to 16 Nm torque.

 27 |Clean the brake caliper bracket from dirt and dust.Use a brake cleaner.

 AUTODOC recommends:

Replacement: wheel bearing -BMW E39. After applying the spray, wait a few minutes.

 28 | Install the brake caliper bracket.

 29|Tighten the brake caliper bracket.Use a drive socket #18.Use a torque wrench.Tighten it to 110 Nm torque.

30| Install the brake pads.

 31Install the brake caliper and fix it.Use HEX No.H7.Use a torque wrench.Tighten it to 30 Nm torque.

 32Install the dust boot caps of the brake caliper guide pins.

         |Install the brake caliper retaining spring.

 reat the fasteners of the wheel hub bearing.Use copper grease.

  35| Treat the surface where the brake disc contacts the wheel rim.Use copper grease.

 

36 Clean the brake disk surface.Use a brake cleaner.

 

  Replacement: wheel bearing -BMW E39. Tip from AUTODOC:

 After applying the spray, wait a few minutes.

 37 |Install the wheel.

 

  AUTODOC recommends:

Important! Hold the wheel while screwing in the fastening bolts. BMW E39

 38Screw in the wheel bolts.Use wheel impact socket #17.

 39Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120Nm torque.

 

 AUTODOC recommends:

BMW E39-Without starting the engine, press the brake pedal several timesuntil it feels firm.

 40 Remove the iarks and chocks